SEARCH

建築用意匠建材メーカー「キャン’エンタープライゼズ」店舗やオフィスの外観から内装、こだわりの住宅に。ブリックタイル、床タイル、石積調の壁材などの製造販売やレンガ、タイル、照明器具の輸入販売。 Top > Manual > LEG・石積み系の擬石タイル　おすすめの施工方法 > MANUAL LEG/stone masonry imitation stone tiles Recommended installation method Download PDF > Check! Points We will introduce some recommended tips for installing the stone-block style imitation stone tile Can'Stone to give the finished product a more realistic look that resembles stacked stones. Tips for constructing stone masonry imitation stone LEG Tight stacking When stacking tightly, there will inevitably be situations where spaces form between the stones. When the main stones are laid on the ground, small pieces of stone are often broken and placed in between to prevent the stones from collapsing and to increase the density of the wall. Stainless steel wire processed CAN'STONE Stainless steel wire is embedded into the back of the tile to physically fasten the wire to the base. Since we will process the product, it will be shipped in the condition shown in the photo. Please clean the base surface beforehand. Check that the base is firmly fixed and that there are no unevenness in the joints of the boards, etc. 1-1: Use a spatula or similar tool to apply dots of adhesive to the back of the stone in the form of balls. Alternatively, apply the product until the back of the tile is no longer visible. 1-2: Please attach the film by referring to the installation instructions . Press it firmly until the adhesive comes out. 1-3: Fix the screw in place so that the stainless steel wire can be pulled out about 100 mm from the stone. ※important point※ Please drive the screw into the side where the stainless steel wire is sticking out. (Photo 1) Do not drive the screws all the way in. (Photo 2) photo1 Photo 2 Stainless steel wire processed CAN'STONE Stainless steel wire is embedded into the back of the tile to physically fasten the wire to the base. Since we will process the product, it will be shipped in the condition shown in the photo. Tight stacking Please clean the base surface beforehand. Check that the base is firmly fixed and that there are no unevenness in the joints of the boards, etc. 1-1: Use a spatula or similar tool to apply dots of adhesive to the back of the stone in the form of balls. Alternatively, apply the product until the back of the tile is no longer visible. 1-2: Please attach the film by referring to the installation instructions . Press it firmly until the adhesive comes out. 1-3: Fix the screw in place so that the stainless steel wire can be pulled out about 100 mm from the stone. ※important point※ Please drive the screw into the side where the stainless steel wire is sticking out. (Photo 1) Do not drive the screws all the way in. (Photo 2) photo1 Photo 2 Please clean the base surface beforehand. Check that the base is firmly fixed and that there are no unevenness in the joints of the boards, etc. 1-1: Use a spatula or similar tool to apply dots of adhesive to the back of the stone in the form of balls. Alternatively, apply the product until the back of the tile is no longer visible. 1-2: Please attach the film by referring to the installation instructions . Press it firmly until the adhesive comes out. 1-3: Fix the screw in place so that the stainless steel wire can be pulled out about 100 mm from the stone. ※important point※ Please drive the screw into the side where the stainless steel wire is sticking out. (Photo 1) Do not drive the screws all the way in. (Photo 2) < Back to list 1) Use glue that is close to the color of the tile you are using. Because the color of the tile and the glue are close, the gaps in the color of the gaps can be filled in, making it look like there is no glue at all. If there are still many gaps, go to ② ②Cut the stones and fill in the gaps. By filling in the gaps, the amount of base coat visible is reduced, resulting in a beautiful look. It is possible to achieve a finish that is close to the original stone masonry design. If you have a sander or similar tool on hand, use it to cut the material to fit the dimensions of the gap. If you want to create a rougher look, use a hammer or something similar to hit the thin parts of the tile to adjust the size and create pieces to fit between them. If the tile aggregate becomes visible on the surface, use Stone Aid, sold separately. CONTACT Various inquiries How to design Attention to design Installation Manual Installation Method Contact Samples, catalogue requests and inquiries Request a sample Check the list

建築用意匠建材メーカー「キャン’エンタープライゼズ」店舗やオフィスの外観から内装、こだわりの住宅に。ブリックタイル、床タイル、石積調の壁材などの製造販売やレンガ、タイル、照明器具の輸入販売。 Top > Manual > CAN’STONE外壁施工方法 （弾力性接着剤張り工法） > MANUAL CAN'BRICK exterior wall construction method (MT-BOND-FLEX elastic adhesive construction method) Download PDF > This is the exterior wall construction method for the brick tile "CAN'BRICK" (MT-BOND-FLEX elastic adhesive laying method). Applicable substrate: Siding/concrete/block/russ mortar By using the elastic adhesive (MT-BOND-FLEX), it can be used on siding substrates that cannot be applied using wet construction methods with resin mortar. Even with conventional mortar substrates, it is more elastic than wet construction methods with mortar, so it can follow the movement of the substrate and suppress the occurrence of cracks. *Since the joints are filled with mortar after the adhesive has hardened, the construction period is longer than with conventional wet construction methods. 1. Surface preparation A. In the case of concrete, block, or raspberry base... After inspecting and cleaning the base, apply an adhesive enhancer (such as Tilement EV-300) with a roller. In the case of a rasmol base, allow sufficient curing time to ensure that it is completely dry and has minimal unevenness before applying the adhesive enhancer. B. In the case of wooden base... Apply waterproof paper and use it as a mortar base, or create a mortar base on top of a mortar board. After allowing sufficient time for curing, carry out the same work as in (a). ※point※ ◎ Avoid carrying out installation in rainy weather and carry out on a sunny day. ◎ When carrying out work during cold seasons, do not carry out work when the temperature is below 5°C or if it is expected that the temperature will drop below 5°C during the curing period after work. 2. Applying adhesive Apply the elastic adhesive (MT-BOND-FLEX) to the base using a 6mm toothed trowel. The area you paint at one time should be the area that will allow you to finish laying the bricks within the allotted time. ◎ If the effective bonding area is 70% or less, use an 8mm toothed trowel to increase the amount of elastic adhesive (MT-BOND-FLEX) applied to the base, or increase the amount of elastic adhesive (MT-BOND-FLEX) applied to the back of the brick. 3. Attachment (Improved Pressure Bonding Method) Apply elastic adhesive (MT-BOND-FLEX) to the entire back surface of the brick until the feet (tentacles) are no longer visible. Press the elastic adhesive firmly until it overflows. ※point※ ◎To check the adhesion of the Elastic Adhesive (ME-05) during application, peel off several sheets every 2m² and check that the Elastic Adhesive (ME-05) is attached to more than 70% of the back side. ◎ If the effective bonding area is 70% or less, use an 8mm toothed trowel to increase the amount of Elastic Adhesive (ME-05) applied to the base, or increase the amount of Elastic Adhesive (ME-05) applied to the back of the stone. ◎ Any adhesive adhering to the surface of the finishing material should be wiped off with a cloth soaked in thinner or similar before it hardens. 4.Curing Allow sufficient curing time for the elastic adhesive (MT-BOND-FLEX) to harden. 5. Joint finishing Fill the joints with the special joint material MT-MEJI using a joint bag, etc. After filling, roughly press down with a joint trowel. Check that it covers at least 1/2 the thickness of the brick and your desired finish (see joint finish), and fill in any gaps with a joint bag, etc. ※point※ ◎ Don't worry if the joint trowel leaves uneven marks as you finish the job, and finally use a brush or scissors to scratch the joints in places to make them look weathered. 6. Protection and water absorption prevention treatment Avoid ventilation and direct sunlight, and protect the stone by covering it with a sheet, etc. Allow the stone to cure for a sufficient period after application, and make sure it is completely dry. Then thoroughly brush off any dust on the stone surface and in the joints. After that, apply the penetrating water absorption prevention agent "REPEL･S" using a sprayer, brush, roller, etc. ◎Since CAN'STONE is a secondary cement product, acid washing is strictly prohibited. < Back to list 6. Protection and water absorption prevention treatment Avoid ventilation and direct sunlight, and protect the stone by covering it with a sheet, etc. Allow the stone to cure for a sufficient period after application, and make sure it is completely dry. Then thoroughly brush off any dust on the stone surface and in the joints. After that, apply the penetrating water absorption prevention agent "REPEL･S" using a sprayer, brush, roller, etc. ◎Since CAN'STONE is a secondary cement product, acid washing is strictly prohibited. CONTACT Various inquiries How to design Attention to design Installation Manual Installation Method Contact Samples, catalogue requests and inquiries Request a sample Check the list

建築用意匠建材メーカー「キャン’エンタープライゼズ」店舗やオフィスの外観から内装、こだわりの住宅に。ブリックタイル、床タイル、石積調の壁材などの製造販売やレンガ、タイル、照明器具の輸入販売。 Top > Manual > CAN’BRICK外壁施工方法 （MT-BOND-FLEX 弾力性接着剤張り工法 > MANUAL CAN'BRICK exterior wall construction method (MT-BOND-FLEX elastic adhesive construction method) Download PDF > This is the exterior wall construction method for the brick tile "CAN'BRICK" (MT-BOND-FLEX elastic adhesive laying method). Applicable substrate: Siding/concrete/block/russ mortar By using the elastic adhesive (MT-BOND-FLEX), it can be used on siding substrates that cannot be applied using wet construction methods with resin mortar. Even with conventional mortar substrates, it is more elastic than wet construction methods with mortar, so it can follow the movement of the substrate and suppress the occurrence of cracks. *Since the joints are filled with mortar after the adhesive has hardened, the construction period is longer than with conventional wet construction methods. 1. Surface preparation A. In the case of concrete, block, or raspberry base... After inspecting and cleaning the base, apply an adhesive enhancer (such as Tilement EV-300) with a roller. In the case of a rasmol base, allow sufficient curing time to ensure that it is completely dry and has minimal unevenness before applying the adhesive enhancer. B. In the case of wooden base... Apply waterproof paper and use it as a mortar base, or create a mortar base on top of a mortar board. After allowing sufficient time for curing, carry out the same work as in (a). ※point※ ◎ Avoid carrying out installation in rainy weather and carry out on a sunny day. ◎ When carrying out work during cold seasons, do not carry out work when the temperature is below 5°C or if it is expected that the temperature will drop below 5°C during the curing period after work. B. In the case of wooden base... Apply waterproof paper and use it as a mortar base, or create a mortar base on top of a mortar board. After allowing sufficient time for curing, carry out the same work as in (a). ※point※ ◎ Avoid carrying out installation in rainy weather and carry out on a sunny day. ◎ When carrying out work during cold seasons, do not carry out work when the temperature is below 5°C or if it is expected that the temperature will drop below 5°C during the curing period after work. 2. Applying adhesive Apply the elastic adhesive (MT-BOND-FLEX) to the base using a 6mm toothed trowel. The area you paint at one time should be the area that will allow you to finish laying the bricks within the allotted time. ◎ If the effective bonding area is 70% or less, use an 8mm toothed trowel to increase the amount of elastic adhesive (MT-BOND-FLEX) applied to the base, or increase the amount of elastic adhesive (MT-BOND-FLEX) applied to the back of the brick. 3. Attachment (Improved Pressure Bonding Method) Apply elastic adhesive (MT-BOND-FLEX) to the entire back surface of the brick until the feet (tentacles) are no longer visible. Press the elastic adhesive firmly until it overflows. ※point※ ◎To check the adhesion of the Elastic Adhesive (ME-05) during application, peel off several sheets every 2m² and check that the Elastic Adhesive (ME-05) is attached to more than 70% of the back side. ◎ If the effective bonding area is 70% or less, use an 8mm toothed trowel to increase the amount of Elastic Adhesive (ME-05) applied to the base, or increase the amount of Elastic Adhesive (ME-05) applied to the back of the stone. ◎ Any adhesive adhering to the surface of the finishing material should be wiped off with a cloth soaked in thinner or similar before it hardens. 4.Curing Allow sufficient curing time for the elastic adhesive (MT-BOND-FLEX) to harden. 5. Joint finishing Fill the joints with the special joint material MT-MEJI using a joint bag, etc. After filling, roughly press down with a joint trowel. Check that it covers at least 1/2 the thickness of the brick and your desired finish (see joint finish), and fill in any gaps with a joint bag, etc. ※point※ ◎ Don't worry if the joint trowel leaves uneven marks as you finish the job, and finally use a brush or scissors to scratch the joints in places to make them look weathered. 6. Protection and water absorption prevention treatment Avoid ventilation and direct sunlight, and protect the stone by covering it with a sheet, etc. Allow the stone to cure for a sufficient period after application, and make sure it is completely dry. Then thoroughly brush off any dust on the stone surface and in the joints. After that, apply the penetrating water absorption prevention agent "REPEL･S" using a sprayer, brush, roller, etc. ◎Since CAN'STONE is a secondary cement product, acid washing is strictly prohibited. < Back to list CONTACT Various inquiries How to design Attention to design Installation Manual Installation Method Contact Samples, catalogue requests and inquiries Request a sample Check the list

404 Page not found. The page you are looking for cannot be found. お探しのページが見つかりませんでした。 TOP

All Posts Aug 21 We have updated our construction examples! CAN'BRICK "Manchester (MC-3)" & CAN'STYLE "Block Face (BLO-2)" Jul 26 We have released new brick tiles that match the 2024 trend color, Peach Fuzz. Jul 26 Terrazzo-style imported tiles - New product information - Jul 26 Notice of shortened business hours due to summer holidays and company events CONTACT Various inquiries How to design Attention to design Contact Samples, catalog requests and inquiries Installation Manual Installation Method Request a sample Check the list