This is the wire construction manual for the masonry-style wall material "CAN'STONE."
・For installation surfaces up to 3m high, please use regular adhesive. (See the URL below)
・This manual provides recommended installation instructions for wall surfaces with a construction surface height of 3m or more.
This is the wire construction manual for the masonry-style wall material "CAN'STONE."
・For installation surfaces up to 3m high, please use regular adhesive. (See the URL below)
・This manual provides recommended installation instructions for wall surfaces with a construction surface height of 3m or more.
This is the wire construction manual for the masonry-style wall material "CAN'STONE."
・For installation surfaces up to 3m high, please use regular adhesive. (See the URL below)
・This manual provides recommended installation instructions for wall surfaces with a construction surface height of 3m or more.
600mmの場合
procedure
1. Tile installation and screw installation
Please clean the base surface beforehand. Check that the base is firmly fixed and that there are no unevenness in the joints of the boards, etc.
1-1: Use a spatula or similar tool to apply dots of adhesive to the back of the stone in the form of balls.
Alternatively, apply the product until the back of the tile is no longer visible.
1-2: Please attach the film by referring to the installation instructions . Press it firmly until the adhesive comes out.
1-3: Fix the screw in place so that the stainless steel wire can be pulled out about 100 mm from the stone.
※important point※
Please drive the screw into the side where the stainless steel wire is sticking out. (Photo 1)
Do not drive the screws all the way in. (Photo 2)
procedure
1. Tile installation and screw installation
1-1: Use a spatula or similar tool to apply dots of adhesive to the back of the stone in the form of balls.
Alternatively, apply the product until the back of the tile is no longer visible.
1-2: Please attach the film by referring to the installation instructions . Press it firmly until the adhesive comes out.
1-3: Fix the screw in place so that the stainless steel wire can be pulled out about 100 mm from the stone.
※important point※
Please drive the screw into the side where the stainless steel wire is sticking out. (Photo 1)
Do not drive the screws all the way in. (Photo 2)
procedure
1. Tile installation and screw installation
1-1: Use a spatula or similar tool to apply dots of adhesive to the back of the stone in the form of balls.
Alternatively, apply the product until the back of the tile is no longer visible.
1-2: Please attach the film by referring to the installation instructions . Press it firmly until the adhesive comes out.
1-3: Fix the screw in place so that the stainless steel wire can be pulled out about 100 mm from the stone.
※important point※
Please drive the screw into the side where the stainless steel wire is sticking out. (Photo 1)
Do not drive the screws all the way in. (Photo 2)
procedure
1. Tile installation and screw installation
1.簡易基礎（砕石+コンクリート）
Stainless steel wire processed CAN'STONE
★擬似石（Garden Wall）の積み方
Stainless steel wire processed CAN'STONE
2-1.鉄筋（縦筋）の設置
Stainless steel wire processed CAN'STONE
2-2.積みながら中空部を充填
Stainless steel wire processed CAN'STONE
3.仕上げ トップキャップの設置
Stainless steel wire processed CAN'STONE
■施工のポイント
Stainless steel wire processed CAN'STONE
600~1200mmの場合
procedure
1. Tile installation and screw installation
Please clean the base surface beforehand. Check that the base is firmly fixed and that there are no unevenness in the joints of the boards, etc.
1-1: Use a spatula or similar tool to apply dots of adhesive to the back of the stone in the form of balls.
Alternatively, apply the product until the back of the tile is no longer visible.
1-2: Please attach the film by referring to the installation instructions . Press it firmly until the adhesive comes out.
1-3: Fix the screw in place so that the stainless steel wire can be pulled out about 100 mm from the stone.
※important point※
Please drive the screw into the side where the stainless steel wire is sticking out. (Photo 1)
Do not drive the screws all the way in. (Photo 2)
procedure
1. Tile installation and screw installation
1-1: Use a spatula or similar tool to apply dots of adhesive to the back of the stone in the form of balls.
Alternatively, apply the product until the back of the tile is no longer visible.
1-2: Please attach the film by referring to the installation instructions . Press it firmly until the adhesive comes out.
1-3: Fix the screw in place so that the stainless steel wire can be pulled out about 100 mm from the stone.
※important point※
Please drive the screw into the side where the stainless steel wire is sticking out. (Photo 1)
Do not drive the screws all the way in. (Photo 2)
1-1: Use a spatula or similar tool to apply dots of adhesive to the back of the stone in the form of balls.
Alternatively, apply the product until the back of the tile is no longer visible.
1-2: Please attach the film by referring to the installation instructions . Press it firmly until the adhesive comes out.
1-3: Fix the screw in place so that the stainless steel wire can be pulled out about 100 mm from the stone.
※important point※
Please drive the screw into the side where the stainless steel wire is sticking out. (Photo 1)
Do not drive the screws all the way in. (Photo 2)
段数
高さ
総重量（石材のみ）
10段
約1.0m
約520kg
12段
約1.2m
約624kg
■高さ設定の考え方
Stainless steel wire processed CAN'STONE
■施工手順 「RC（鉄筋コンクリート）芯材工法」
Stainless steel wire processed CAN'STONE
1.基礎（最重要）
Stainless steel wire processed CAN'STONE
★擬似石（Garden Wall）の積み方
Stainless steel wire processed CAN'STONE
2-1.鉄筋（縦筋）の設置
Stainless steel wire processed CAN'STONE
2-2.積みながら中空部を充填
Stainless steel wire processed CAN'STONE
3.仕上げ トップキャップの設置
Stainless steel wire processed CAN'STONE
